Capstans

[Farrell]

Well, I think I am on board. My point was that action geometry is not a
component of Stanwood's patents (I believe that to be true). So talking
about "Stanwoodizing" and talking about action geometry (capstan
re-installation or re-location) have nothing to do with one another,
reletive to patents. Richard indicated an intent to "Stanwoodize" (I presume
install Precision TouchDesign) in the future. If this is done without
consultation with David or an authorized agent, he/anyone should not refer
to this work as Precision TouchDesign. However, Richard did not indicate his
exact intent regarding future plans for "Stanwoodizing".

I agree wholeheartedly with your point however regarding only using Stanwood
or Precision TouchDesign when Precision TouchDesign will be properly
installed.

Terry Farrell
Piano Tuning & Service
Tampa, Florida
mfarrel2@tampabay.rr.com

----- Original Message -----
From: "Jon Page" <jonpage@mediaone.net>
To: <pianotech@ptg.org>
Sent: Saturday, January 06, 2001 10:15 PM
Subject: Re: Capstans


> At 08:30 PM 01/06/2001 -0500, you wrote:
> > > Watch yourself here...David might get all over you for even implying
> > > use of his technique without being an installer.  Very shaky ground
here.
> > > If figures have not been calculated by an authorized Precision
TouchDesign
> > > agent, they can not be termed Stanwood.
> >
> >I think I am correct to say that anything to do with weighing off hammers
> >and keys (front weights) and saying Precision TouchDesign
> >in the same sentence should/must indeed come from an authorized Precision
> >TouchDesign agent. However, anything to do with action geometry, such as
> >relocating capstans, is something that technicians have been doing for
many
> >decades (at least some have anyway). I do not believe David Stanwood has
any
> >patents covering action geometry, and specifically, capstan relocating.
But
> >I have not read the text of his patents - but I think they only cover
> >weighing off/balancing strike weight, key front weight, and the
> >formulas/calculations required to get them.
>
> To say that you will "Stanwoodize" without specifications is not applying
> David's
> system, and as such should not have his name attached to it. David's
system
> is a
> calculated process and to lend his name to a generic 'rewhatever' is
> misleading,
> as unintentional as it was.
>
> I'm certain David would like his process to be well known with everyone
but
> would not
> appreciate the loss of product identity through casual lingo. Some product
> names have,
> through casual usage, replaced product nomenclature; Bandaid for adhesive
> bandages,
> Kleenex for facial tissue.  It would be a long time before "Precision
> TouchDesign" or
> "Stanwood" becomes a household words but to infer David's process for
general
> action geometry modification is completely incorrect.
>
> I understand Richard's enthusiasm and interest in action optimizing, I
just
> want to
> clarify terminology.
>
> Get on board...  get the lead out   :-)
>
> Jon Page
>
>
> >Terry Farrell
> >
> > > At 11:40 PM 01/06/2001 +0100, you wrote:
> > > >Hi list
> > > >
> > > >Have a problem I would like to consult with you all on. Ran into
> > > >a grand what has loose capstans..... to the point that they sink
> > > >right down in deep after a few blows of the key. Nice eh ??
> > > >
> > > >Now this grand is going to get a Stanwoodizing job in the not too
> > > >distant future so I will have a chance then to really fix the
> > > >problem... but in the meantime it needs to be in near concert
> > > >condition. Soooo....
> > >
> > > Watch yourself here...David might get all over you for even implying
> > > use of his technique without being an installer.  Very shaky ground
here.
> > > If figures have not been calculated by an authorized Precision
TouchDesign
> > > agent, they can not be termed Stanwood.
> > >
> > > >What is your prefered method of temp fixing loose capstans on a
> > > >quality instrument that you know for certain you are going to fix
> > > >up nicely in a few months ??
> > >
> > > I don't know if there is an easy way aside from removing the capstan
and
> > > swabbing
> > > the hole with CA or a veneer shim.  You can make a test and drip some
CA
> >in
> > > along side.
> > > Remove the stack, feed it in, turn them occasionally to keep them from
> > > freezing.
> > >
> > > I cut 1/4" plugs from old keys to plug the drilled-out holes when
moving
> > > capstans
> > > within proximity of the old hole.  I orient the grain in the same
> >direction
> > > as well.
> > >
> > > Jon
> > >
> > >
>
> Jon Page,   piano technician
> Harwich Port, Cape Cod, Mass.
> mailto:jonpage@mediaone.net
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
>