Alan, Tis no rumor. Joe Goss imatunr@srvinet.com www.mothergoosetools.com ----- Original Message ----- From: "Alan R. Barnard" <mathstar@salemnet.com> To: <pianotech@ptg.org> Sent: Friday, July 26, 2002 7:54 PM Subject: Re: Thermosetting glue > I just emailed Ruth McCall for more info. In working with it, I know it got > reeeeeeal thin when I applied the heat gun. It just floooooows so nicely > into those cracks. I made a very old grand bridge work fine despite huge and > numerous cracks and pins so loose I removed about a dozen by just lifting > them out with my fingers, no resistance at all! I became a believer. > > Anyway, I have a rumor that Ruth is/was selling her business and retiring. > If I get a reply I'll post the info here. > > Cheers, > > Alan > ----- Original Message ----- > From: "Carl Meyer" <cmpiano@attbi.com> > To: <pianotech@ptg.org> > Sent: Friday, July 26, 2002 7:48 PM > Subject: Re: Thermosetting glue > > > > I would like to see the viscosity specs for thermoset103. > > Water has a viscosity of approx "1" at room temp. Epotec 301 has a > viscosity of "100". Liquid wood, west systems thinnest, clear coat etc. has > a viscosity of "500-1000". Find me an epoxy with a viscosity of less than > 100 and I'll order some. > > > > Thanks! > > > > Carl Meyer Assoc. PTG > > Santa Clara, California > > cmpiano@attbi.com > > > > > > ----- Original Message ----- > > From: "Alan R. Barnard" <mathstar@salemnet.com> > > To: <pianotech@ptg.org> > > Sent: Friday, July 26, 2002 3:51 PM > > Subject: Re: Thermosetting glue > > > > > > > Hi. I posted the original comments on McCall's Thermoset 103. > > > > > > This stuff is very fluid and when heated becomes about like water. It > would > > > definitely NOT be appropriate for leather, felt, metal, etc., or > anything > > > that might need removing later. > > > > > > It is FABULOUS for cracked and split wood in bridges, aprons, frame > members > > > (including old wooden stack brackets, ala Chickering, etc.) and any > other > > > place where you need to restore the strength of wood and fill minute > cracks > > > in laminations, etc. > > > > > > I'm guessing it would be wonderful in pinblocks, as well-- especially > > > grands--but haven't had the nerve to try it for a paying customer. > > > > > > Alan R. Barnard > > > Salem, MO > > > > > > ----- Original Message ----- > > > From: "gordon stelter" <lclgcnp@yahoo.com> > > > To: <pianotech@ptg.org> > > > Sent: Friday, July 26, 2002 4:25 PM > > > Subject: Thermosetting glue > > > > > > > > > > > > > > I know that I will be indicted by some as a heathen > > > > for this question but, frankly, who cares? > > > > I do a lot of player work, and for years have > > > > wondered if there is a glue that has the properties of > > > > hide glue ( softens when heated, perhaps water > > > > soluble, etc..) but ISN'T. I do not particularly > > > > enjoy breathing the reek of animal sinews steaming > > > > away under my nose ( somewhat toxic) all day, but do > > > > not wish to use an irreversible glue on a stack, > > > > either. > > > > The water soluble aspect makes removal of > > > > residues easy, but I would even consider non - aqueous > > > > (such as glue gun) if there was one that set up slowly > > > > enough to get the pneumatics pressed firmly into place > > > > before it gets too tight to locate them. And this may > > > > be a benefit in regions ( like mine ) where humidity > > > > swings tend to loosen hide glue, anyway.As long as the > > > > pneumatics could be removed in the future. I'm > > > > interested. Anyone? > > > > Gordon Stelter > > > > > > > > __________________________________________________ > > > > Do You Yahoo!? > > > > Yahoo! Health - Feel better, live better > > > > http://health.yahoo.com > > > > > > > > > > >
This PTG archive page provided courtesy of Moy Piano Service, LLC