Way cool Mark! Joe Goss imatunr@srvinet.com www.mothergoosetools.com ----- Original Message ----- From: "Mark Cramer" <Cramer@BrandonU.CA> To: "College and University Technicians" <caut@ptg.org> Sent: Tuesday, May 25, 2004 2:14 PM Subject: RE: mini belts > Joe, > > thanks for making so many interesting/innovative tools available. > > I have been using both 1" and 4" paddles for a number of years now. > > The 1" paddles were inspired by Carl's (sorry, his last name evades me) > clever "electric-carving knife" adaptation. (the 4" paddles were part of > this purchase) > > Though his crafty device works well, I wasn't happy with my ability to keep > hammer crowns square with the 1/2" sandpaper, nor the short stroke afforded > by the electric tool. > > I made the first set of 1" paddles out of desperation, needing to get an > action back in the piano, within the tuning appointment. They were made from > a maple paint-stir-stick, with coarse cloth-backed paper. > > I was amazed! > > Deeply-grooved bass-hammers could be filed in this fashion (2-at-a-time), > retaining the original shape of the hammer shoulders, and keeping crowns > square, and a full section filed in 5 minutes... or less! > > Finishing with the 4" paddles and finer paper leaves a very precise job, > with little, if any tell-tale "swindling" of shoulders, common to gang-filed > angled hammers. > > One thing I havn't come up with yet, is a quick-change method for the > sandpaper (though it appears you've found one). I'll I can say, is don't > bother with velcro! :>) > > Mark Cramer, > Brandon University > > > > > > -----Original Message----- > From: caut-bounces@ptg.org [mailto:caut-bounces@ptg.org]On Behalf Of Joe > And Penny Goss > Sent: Tuesday, May 25, 2004 12:32 PM > To: oleg-i@noos.fr; College and University Technicians; Pianotech > Subject: Re: mini belts > > > Hi Isaac, It is no trick. Just a faster removal of felt, that is if you have > the correct grit 50 or 60 and fresh paper. Then finish up with fine grit > down to 240 or so. We have three widths of paddles. 1/2" , 1", and 2" The > 1/2" can be used on any hammer, but is especially designed for bass and > angled hammers. The 1" is for inline hammers and the tenor if they are not > on an angle. > The 2" paddle is designed to be able to have the paper replaced in seconds > for a different grit and is used on straight hammers and to level the > striking point of all hammers. > My paddles are especially useful on upright actions ( the action must be > removed ) but allow the tech to develop a technique and let them use the > same on both uprights and grands. > Pictures on my site below > Joe Goss > imatunr@srvinet.com > www.mothergoosetools.com > ----- Original Message ----- > From: "Isaac OLEG" <oleg-i@noos.fr> > To: "College and University Technicians" <caut@ptg.org> > Sent: Tuesday, May 25, 2004 10:21 AM > Subject: RE: mini belts > > > > > > Ping Pong paddle ? are these Chinese technical tricks ? > > > > Is not it heavier than any filing setup ? > > > > Isaac OLEG > > > > > > -----Message d'origine----- > > De : caut-bounces@ptg.org [mailto:caut-bounces@ptg.org]De la part de > > Ron > > Koval > > Envoyé : lundi 24 mai 2004 20:44 > > À : caut@ptg.org > > Objet : mini belts > > > > > > Lance, > > > > Thanks for posting this. I'd seen over the years all sorts of sanding > > paddles, but never thought of using a ping pong paddle. I had an old > > one in > > the basement, and gave it a try.... WOW! It helped me to square off > > the > > sides and top to make it more rectangular, and shorten the handle, but > > for > > the rough work, it really speeds things up. And less potentially > > damaging > > than the Dremel sanding barrel. > > > > Ron Koval > > Chicagoland > > > > > > > > > > > > Wim, just my experience. I have one, but, I now slip wood under the > > shanks of upright or block up tails on grands and use a ping pong > > paddle > > to do the two side facets or rough initial stuff with about 40-60 > > grit, > > then refine with strips. This actually faster for me. I just never > > went back to the belt. > > > > Lance Lafargue, RPT > > LAFARGUE PIANOS > > New Orleans Chapter, PTG > > 985.72P.IANO > > llafargue@charter.net > > > > _________________________________________________________________ > > Is your PC infected? Get a FREE online computer virus scan from > > McAfee® > > Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963 > > > > _______________________________________________ > > caut list info: https://www.moypiano.com/resources/#archives > > > > > > > > _______________________________________________ > > caut list info: https://www.moypiano.com/resources/#archives > > _______________________________________________ > caut list info: https://www.moypiano.com/resources/#archives > > _______________________________________________ > caut list info: https://www.moypiano.com/resources/#archives
This PTG archive page provided courtesy of Moy Piano Service, LLC