Thanks Mike, good suggestion and I'll use this soon. My regards, Gordon Holley On 16 Oct 2002 at 7:28, Mike Kurta wrote: > Gordon: > To remove the square nuts easily from the stickers after the rubber > grommets have broken away, take a 1/4" drive socket extension, any length. > Chuck it into your drill, and voila! You now have a custom nut removal > tool. The square end fits the nut perfectly. You may have to drill up > into the female end of the extension to create clearance for the threads on > the rod, but its easily done. If the nuts are very tight, you may have to > hold the rod with a small vise grip to keep it from twisting. Also, if the > tool slips in your drill chuck, grind 3 flats on the male end, or if you > want to get fancy, weld a screwdriver bit to the end and put it in your > power screwdriver. > Mike Kurta > ----- Original Message ----- > From: "Gordon Holley" <gholley@hi-techhousing.com> > To: "Pianotech" <pianotech@ptg.org> > Sent: Tuesday, October 15, 2002 11:45 AM > Subject: Re: Hammer Spring Rail Replacement > > > > Thanks Gordon. When I took the rail off and inspected it and the > > springs, it was straight and not warpped. However, your suggestion > > will be so helpful in the future should I ever worked on another on > > of these actions (G). Rubber grommets hardened, breaking off when I > > removed the sticker from the fork, screwed threads of the sticker > > above the nut rusted or coated with mouse pi_ _. Hope I can get the > > nuts off when I put new grommets on. Boy, first one of these I've > > worked on and I get a crudded mess. However, guess you might as well > > grin and get on with it. > > Thanks again Gordon, Regards, Gordon Holley > > On 15 Oct 2002 at 7:34, gordon stelter wrote: > > > > > On the subject of spring rails: Often I find uneven > > > touch on uprights due to warpage in the spring rail. I > > > remedy by screwinmg a very small aluminum angle along > > > the edge of the spring rail, notched for action > > > brackets, etc.. > > > --- Gordon Holley <gholley@hi-techhousing.com> wrote: > > > > Thanks Jerry for the assistance, do appreciate the > > > > help. > > > > Regards, Gordon > > > > On 15 Oct 2002 at 6:54, G GRAVINA wrote: > > > > > > > > > Gordon, > > > > > > > > > > I've had success replacing whole sets of springs > > > > in original > > > > > rails. Replacement springs are available from > > > > Schaff, part numbers 519A, > > > > > 519B and 3777. > > > > > > > > > > Jerry Gravina, RPT > > > > > Babylon, NY > > > > > > > > > > At 09:18 AM 10/14/2002 -0500, you wrote: > > > > > >List. I need information on securing a new > > > > hammer spring rail for a > > > > > >Baldwin-Howard, Spinet, drop action, with > > > > stickers. Some springs are > > > > > >broken, others are all bent, in general hammers > > > > won't return. I > > > > > >found in the archives a discussion between John > > > > Ross, Newton Hunt, > > > > > >Patrick Draine and Clyde Hollinger, Aug 1999, a > > > > source of Pratt Winn > > > > > >and Wade Boggs, where John Ross suggests they > > > > will build a new one if > > > > > >one were to send them the old one. They would > > > > duplicate it with a > > > > > >replacement rail for a reasonable price. > > > > > >Does anyone have further information on this with > > > > an address, phone > > > > > >number, e-mail address, etc. > > > > > >Thank you all for the pending help. Regards, > > > > Gordon Holley, Goshen, > > > > > >IN > > > > > >_______________________________________________ > > > > > >pianotech list info: > > > > https://www.moypiano.com/resources/#archives > > > > > > > > > > _______________________________________________ > > > > > pianotech list info: > > > > https://www.moypiano.com/resources/#archives > > > > > > > > > > > > _______________________________________________ > > > > pianotech list info: > > > https://www.moypiano.com/resources/#archives > > > > > > > > > __________________________________________________ > > > Do you Yahoo!? > > > Faith Hill - Exclusive Performances, Videos & More > > > http://faith.yahoo.com > > > _______________________________________________ > > > pianotech list info: https://www.moypiano.com/resources/#archives > > > > > > _______________________________________________ > > pianotech list info: https://www.moypiano.com/resources/#archives > > _______________________________________________ > pianotech list info: https://www.moypiano.com/resources/#archives
This PTG archive page provided courtesy of Moy Piano Service, LLC